Q235B碳钢板: 厚度公差, 边缘状况和切割
Q235B carbon steel plate is the workhorse structural plate of the Chinese and Southeast Asian market. It is a mild carbon steel with a minimum yield strength of 235 兆帕, delivered in the hot rolled condition, and it covers the largest volume of any single plate grade in general fabrication. Fabricators buy it by the tonne for base plates, 角撑板, 框架, hoppers, 平台, machine guards and temporary works.
The problems that arise with Q235B plate are rarely metallurgical. They are dimensional and practical: a plate that is 0.4 mm under nominal thickness, a plate that arrived with a rolled edge from a shear, a plate whose cut edge was never primed and now rusts under the paint, or a plate that was ordered as 10 mm and turned out to weigh like 9 mm across a whole bundle. This guide explains what Q235B plate is, how its thickness and edge tolerances actually work, how cutting choices affect the finished part, and which purchasing details prevent the usual arguments at the receiving bay.
1. What Q235B Carbon Steel Plate Is and Where It Is Used
Q235B is defined in GB/T 700, the Chinese standard for carbon structural steel. The designation breaks down into a minimum yield strength of 235 MPa and a B quality level, which means the steel is killed (fully deoxidised) and has a specified impact toughness at room temperature, with tighter limits on sulphur and phosphorus than the A grade. It is not a fine grain or a low alloy grade; it is a plain carbon manganese steel intended for welded and bolted structures.
Plate is produced by hot rolling a slab to thickness and then cooling. It is supplied in the as rolled condition, with a mill scale surface, and is not normally normalised or annealed unless the order asks for it. That production route explains the surface and the residual stress pattern: the plate is straight when it leaves the mill, and it moves when it is cut because the internal stress is released.
典型应用包括:
- Base plates, anchor plates and machine foundation plates.
- 结构框架, 括号, gussets and stiffeners.
- Platforms, 走道, stair stringers and floor plates.
- Hoppers, 垃圾箱, chutes and light duty tanks.
- Machine guards, covers and enclosures.
- Scaffolding components, temporary works and site fabrication.
- General engineering where strength is moderate and cost is decisive.
Q235B is not a pressure vessel grade, not a low temperature grade, and not a grade for dynamic loading at sub zero temperatures. It is a general structural plate, and the correct choice for the applications above is usually driven by availability and price rather than by a detailed design calculation.

2. 牌号和化学成分
国标/T 700 specifies the chemistry for Q235B, and the limits are wide because the grade is intended to be made from a range of raw materials. The table below gives the standard limits alongside the values that matter in fabrication.
| 元素 | Q235B limit (%) | Effect in fabrication |
|---|---|---|
| C | 0.12 到 0.20 | Strength and hardenability; higher carbon narrows the weld window |
| 和 | 0.30 最大限度 | 脱氧; affects slag and weld appearance |
| 锰 | 0.30 到 0.70 | Strength and toughness; low manganese limits impact values |
| 磷 | 0.045 最大限度 | Segregation and cold brittleness; the B grade tightens this |
| S | 0.045 最大限度 | Hot cracking and lamellar tearing risk |
| Alt | 0.015 min when requested | Fine grain practice; 提高韧性 |
| CE equivalent | 通常 0.30 到 0.38 | 可焊性; 多于 0.40 requires preheat on thick sections |
Two practical points follow. 第一的, Q235B covers a wide carbon range, and a plate at 0.20 percent carbon behaves differently from one at 0.13 percent when it is welded or flame cut: the higher carbon plate hardens more in the heat affected zone and is more likely to crack in a thick section without preheat. 第二, the B suffix is a quality claim about phosphorus and sulphur and impact testing, so a certificate that shows only yield strength is incomplete.
3. 机械性能
| 财产 | 典型值 | 标准最小值 | Design note |
|---|---|---|---|
| Yield strength ReH | 245 到 300 兆帕 | 235 兆帕 | Thickness dependent in GB/T 700 |
| 拉伸强度Rm | 400 到 490 兆帕 | 370 到 500 兆帕 | Range narrows as thickness rises |
| 伸长率A | 22 到 30 % | 21 % 在 16 mm and below | Bend radius and forming limits |
| 影响, 夏比V 20 ℃ | 27 J minimum for B | 27 J | Not a low temperature grade |
| 密度 | 7.85 克/立方厘米 | 参考值 | Plate weight calculation |
| 弹性模量 | 206 GPa | 参考值 | Stiffness of frames and platforms |
| Hardness HB | 120 到 160 | 未指定 | Machinability and tool life |
The yield strength is quoted by thickness band, and this is where a specification can go wrong. 国标/T 700 reduces the minimum yield for thicker plate, 所以一个 40 mm plate is not required to reach 235 MPa in the same way a 10 mm plate is. A designer who applies 235 MPa to a 40 mm section may be overestimating the material, and a fabricator who compares a 40 mm plate against a 10 mm plate and finds it softer is not looking at a defective plate.
4. 尺寸和公差
Thickness tolerance is the single most negotiated number in a Q235B plate order, because plate is sold by weight and the tolerance translates directly into money. The table below reflects the common commercial tables; the purchase order should name the standard and the tolerance class, not just the nominal thickness.
| 范围 | 范围 | 典型公差 | 检查 |
|---|---|---|---|
| 厚度 3 到 5 毫米 | 3.0 到 5.0 | 加或减 0.3 毫米, 或减去 0.4 mm only by agreement | Micrometer at five points |
| 厚度 6 到 16 毫米 | 6.0 到 16.0 | 加或减 0.4 到 0.6 毫米 | Micrometer at five points |
| 厚度 20 到 40 毫米 | 20 到 40 | 加或减 0.7 到 1.1 毫米 | 千分尺, avoid rolled edges |
| 宽度 | 1000 到 2500 毫米 | 0 加 10 毫米 | Tape at both ends |
| 长度 | 2000 到 12000 毫米 | 0 加 15 毫米 | Tape along both edges |
| 平整度 | All plates | 10 mm per metre for 3 到 10 毫米, 8 mm per metre above | Straight edge and feeler |
| 剪边 | Cut to size | Rake 2 到 4 毫米开 10 毫米板, 毛刺 0.3 最大毫米 | Visual and straight edge |
| 外倾角 | Full length | 0.2 长度的百分比 | String line |
A minus only tolerance is common in the market because it saves the mill metal, and it is legal when it is agreed. The commercial consequence is that a 10 mm plate ordered with a minus 0.6 mm allowance weighs about 6 percent less than the theoretical weight, and a buyer who pays by theoretical weight is paying for steel that is not there. The correct response is either to order to a minimum thickness and accept a plus tolerance, or to pay by actual weighbridge weight and inspect the thickness on arrival.
The second dimensional trap is the rolled edge. Shearing a plate does not produce a square edge; it produces an edge with a rake, and the rake grows with thickness. 上一个 20 毫米板, the rake can be 4 到 6 毫米, which means the edge is not vertical and a joint that assumes a square edge will have a gap. Plasma and waterjet cutting produce a squarer edge, at a different cost.

5. Cutting and Edge Preparation
剪毛 is the cheapest way to cut a straight line, and it is limited by thickness and by the rake it leaves. A guillotine shear on 6 mm plate is fast and accurate in length, but the cut edge is slightly inclined and work hardened. That edge is acceptable for a base plate that will sit on concrete, and unacceptable for an edge that will be welded without grinding.
Plasma cutting handles any thickness and any profile, and leaves a heat affected zone with a hardened rim. On Q235B with 0.18 percent carbon, the rim can reach 40 到 45 HRC, which is hard enough to damage a drill or a tap if the hole is plasma cut and then machined. The practical fix is to leave 2 mm of stock and machine through the hardened layer, or to cut the hole with a smaller plasma kerf and drill it out.
Flame cutting is the traditional method for thick plate. It requires preheat on plate above about 25 毫米, and it leaves a wider heat affected zone than plasma. For Q235B the process is forgiving, but a flame cut edge on a plate that will be painted needs the scale and dross removed before priming, or the paint will fail along the edge within a season.
Waterjet cutting leaves no heat affected zone and a square edge, and it is the right choice when the edge will be machined or when the plate is already coated. It is slower and more expensive per metre, and the abrasive cost rises quickly on thick plate.
Sawing is used for thick plate that needs a machined edge, such as a base plate with a flatness requirement. A band saw leaves a smooth edge and no heat effect, but the cut takes time and the plate has to be handled on a table.
Edge preparation for welding is not optional. 氧化皮, rust and paint must be removed for at least 25 mm either side of the joint. Q235B with a mill scale surface welds acceptably if the scale is wire brushed, but a plate that has been stored outdoors and has a rust layer needs grinding back to bright metal. Welding over rust produces porosity and slag inclusions, and the resulting joint will fail an inspection even if it looks sound.
6. 选型及安装规则
- Order to a minimum thickness where the plate is a structural member, and state whether a minus only tolerance is acceptable.
- Decide the edge process before the order. A sheared edge and a plasma edge are not interchangeable for a welded joint.
- For plate above 20 mm that will be welded, ask for the carbon equivalent and preheat accordingly. A 0.20 percent carbon plate at 30 mm needs preheat even though the grade is mild.
- Inspect thickness on arrival with a micrometer, not a tape, and record the readings against the certificate.
- Store plate on timber, 清除地面, and keep the bundles tagged so the heat number can be traced after the bundle is opened.
- Prime cut edges before the plate leaves the shop. A Q235B edge that is left bare will rust in transit and the rust will bleed through the finish coat.
- Do not substitute Q235B for Q355B in a design that was calculated for the higher yield. The plate is cheaper and the section is the same, but the capacity is not.
Where the plate is used as a base for a frame that also carries galvanized components, the coating system has to be compatible. 这 镀锌钢带 DX51D page covers the coated strip counterpart, and mixing bare Q235B plate with galvanized strip in one assembly requires that the plate be primed before the two are brought into contact.
Where a small flat bar section is required rather than plate, the same grade is available in bar form; 这 Q235B碳钢扁钢 page covers the rolled bar product, which is produced to different dimensional tolerances than plate.
7. 常见的误解
误解一: Q235B is Q235B, whatever the mill. The standard allows a range of chemistry, and two plates that both meet it can differ in carbon equivalent, 韧性和焊接性. The certificate is the only way to know which one you have.
Misconception two: thickness tolerance is a rounding error. 上一个 10 毫米板, a minus 0.6 mm tolerance is 6 percent of the weight. 上一个 20 tonne order that is more than a tonne of steel.
Misconception three: a shear cut is as good as a plasma cut. It is cheaper and faster, and it leaves a raked, work hardened edge. For a welded joint the difference has to be ground out.
Misconception four: mild steel does not need preheat. Mild refers to the alloy content, not to the welding behaviour of a 30 mm section. Thick sections conduct heat away and cool fast, and the heat affected zone hardens.
误区五: mill scale protects the plate. Mill scale is a rolled oxide that is brittle and loosely bonded. It traps moisture and undercuts paint adhesion, and it must be removed before a protective coating is applied.
8. 常见问题解答
What is the difference between Q235A and Q235B?
The B grade has tighter phosphorus and sulphur limits and a specified room temperature impact value. The A grade is not impact tested and is not intended for welded structures that carry dynamic load.
How is Q235B plate weight calculated?
Length times width times thickness times 7.85 克/立方厘米. A 10 mm plate of 1500 x 6000 mm weighs about 707 kg at nominal thickness, 和 665 kg if it is delivered at the minus tolerance limit.
Q235B可以镀锌吗?
是的, and it is one of the most common substrates for hot dip galvanizing. The silicon content matters: a silicon level near 0.1 percent can produce a very thick, 脆性涂层, so the galvanizer should check the chemistry before dipping.
What is the maximum thickness of Q235B plate?
Standard plate mills supply up to about 60 毫米, with heavier sections available on request. 多于 40 mm the yield strength minimum drops according to the standard’s thickness table.
Does Q235B need a mill certificate?
用于结构工程, 是的. The certificate ties the plate to a heat number and gives chemistry, mechanical results and the impact test that distinguishes the B grade from the A grade.
How much does a plate bow after cutting?
It depends on the residual stress in the plate and on the cut pattern. Cutting a large plate into long strips releases stress asymmetrically and the strips can bow several millimetres. Cutting a symmetric pattern keeps the balance and the bow is smaller.
9. 下一步
If you are buying Q235B plate, put the standard, the thickness with a minimum, the tolerance class, the cut process and the certificate requirement on the enquiry. Those five items decide the delivered weight, the weldability and the condition of the edge, and they are much cheaper to agree before shipment than to argue about after arrival.
相关产品页面: Q235B碳钢扁钢, 镀锌钢带 DX51D.
进步